Skip to content
Petrol fire fighting pump with its priming cap off beside a bucket of water and a suction hose with strainer at a farmhouse tank

How to Prime a Fire Fighting Pump (and Why It Won't Draw Water)

Petrol fire fighting pump with its priming cap off beside a bucket of water and a suction hose with strainer at a farmhouse tank

Short answer: To prime a fire fighting pump, fill the pump housing with water before starting it; Bianco's manual recommends at least 2 litres, filled fully if possible, with the suction hose also full. Fit the strainer, check oil and fuel, then start the engine and allow time. A self-priming pump may need several attempts before it draws; running it dry damages the mechanical seal.

If the pump drew water at the first attempt, the priming procedure below is all you need. If it ran but delivered nothing, the troubleshooting table further down summarises the causes the manufacturers identify, beginning with the one owners find hardest to detect: an air leak in the suction hose.

How do you prime a fire fighting pump?

Fill the pump housing with water, seal the filler and start the engine with the suction hose already submerged. The steps below follow Bianco's manual for its Vulcan fire pumps; Water Master's manual for its MH30-2 engine-driven pump gives the same priming instructions.

  1. Fit the strainer to the end of the suction hose; both makers strongly encourage a foot valve (non-return valve) directly above it.
  2. Place the pump as close to the water as possible and submerge the suction inlet more than 150 mm below the surface.
  3. Check the engine oil, since both pumps leave the factory without oil, then check the fuel.
  4. Remove the pump filler cap and pour in water: at least 2 litres, preferably until full. Fill the suction hose as well if you can.
  5. Refit the filler cap firmly, turn the fuel valve on, close the choke and set the throttle about two-thirds open.
  6. Switch the engine on and pull the starter. As the engine warms, open the choke, then set the throttle for the flow you need.

Is a self-priming pump really self-priming?

Only once water is already inside it. Answer engines disagree on this point: one AI model queried for this guide stated that centrifugal fire pumps are not self-priming, whereas the manufacturers describe their portable pumps as self-priming. Bianco's troubleshooting section resolves it: these pumps can draw water up from the source only if there is water already in the pump. The Vulcan is rated to self-prime from up to 6 m below the inlet.

The manufacturers also set realistic expectations on timing. Both manuals explain that initial priming may require multiple attempts, particularly with long suction lines or a significant lift, because a larger volume of air must be expelled first. If the pump does not prime, stop it, let it rest briefly and try again; the manuals call this normal rather than a fault.

Why won't my fire pump draw water?

Usually because air is entering somewhere on the suction side. The troubleshooting tables in both manuals list the causes below, with the corrective action for each.

Cause listed by the makers Corrective action in the manuals
Pump not primed Reprime, then inspect the suction side for air leaks
Pump takes too long to prime Look for an air leak or a defective check valve
Suction lift too high Reduce the lift by placing the pump nearer the water level
Suction inlet not deep enough Keep the inlet more than 150 mm below the surface
Suction or strainer blocked Remove the obstruction and fit a strainer
Suction line admitting air Repair or replace the line; tighten the connections

Air leaks are the most difficult to locate, because a suction hose operates under vacuum and therefore does not drip. A poster on Prospecting Australia makes exactly that point after a pump kept losing prime, advising owners to check the primer cap seal and look for cracks or punctures in the hose. A commenter on a YouTube video titled Fire Pump Basics recommends a check valve on the end of the suction line to hold prime. On Whirlpool, a reply to an owner whose bore pump ran without delivering points first to a damaged or blocked foot valve.

How do you avoid damaging the pump while priming?

Never run it dry; never let it operate for long against a closed nozzle either. Bianco warns that running dry or without enough water damages the mechanical seal quickly and voids the warranty. Its manual also describes cavitation, a distinctive sound like gravel inside the pump caused by excessive suction demand; the remedy is to restrict the outlet or reduce the suction requirement.

Owners add a related warning about overheating. Commenters on two YouTube videos, Fire Pump Basics and a pool pump wildfire setup, warn that water sitting in a running pump with no outlet open heats up and harms the seals. A poster on Whirlpool's electric fire pump thread gives the simplest version: do not run them dry.

When should you practise priming?

Before the season begins, never on the day of a fire. Victoria's Country Fire Authority asks households to test equipment before each fire season, replace old fuel and teach every adult in the home to use the pump. On ExplorOz, a poster who attends fires describes how often owners say they have a pump, then admit it does not work.

Picture a farmhouse with a tank on a stand and a Honda-engined pump on a slab beside it. When the first smoke of the season appears over the ridge, the owner pulls the cord on a pump that has sat dry since autumn. It roars but delivers nothing, because the housing is empty and a split in the suction hose admits air. A test run in October, with a bucket of water and a sound suction hose, would have found both faults. A pump you have primed once is a pump you can prime under pressure.

Ring me on 03 7073 2116 if your pump still will not draw after these checks. The Water Master range includes the Water Master Fire Hose Kit, with a 4 m suction hose and strainer, at $181.50 on 9 November 2026. Every item carries our price-beat promise. We handle warranty for you on any pump bought from us, while delivery is charged by state at checkout.

You May Also Like:

Hayden Pearson profile picture

Hayden Pearson

Learn More

About the author:
“I have a real passion for helping transform outdoor spaces so people can relax, connect and entertain with confidence and pride. With My Acre, I love guiding homeowners to create beautiful and functional outdoor living areas."

Hayden from My Acre

Want a written quote?

Tell me what you are after. I send it the same business day.